Ford Sierra


Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
    3.1. Cars with petrol engines
   - 3.2. Cars with diesel engines
      - 3.2.1. Changes in a design of the car with 1988 to 1993
         3.2.1.1. The engine 2,3 дм3
         - 3.2.1.2. The engine 1,8 дм3
            3.2.1.2.1. Technical characteristics
            3.2.1.2.2. A head of the block of cylinders
            3.2.1.2.3. The block of cylinders
            3.2.1.2.4. The Krivoshipno-shatunnyj mechanism
            3.2.1.2.5. System timing
            3.2.1.2.6. Greasing system
            3.2.1.2.7. Cooling system
            3.2.1.2.8. Fuel system
            3.2.1.2.9. The tightening moments
            3.2.1.2.10. Engine adjustment
          3.2.1.3. Fuel system
          3.2.1.4. The repair which is not demanding removal of the engine
         3.2.1.5. Removal and engine installation
         3.2.1.6. Engine dismantling
         3.2.1.7. Check of details
         3.2.1.8. Check of backlashes of a cranked shaft and rods
         3.2.1.9. Engine assemblage
         3.2.1.10. Greasing system
         3.2.1.11. Cooling system
         3.2.1.12. Coupling
         3.2.1.13. A mechanical five-speed transmission of type МТ 75
         3.2.1.14. A power shaft and the back bridge
         3.2.1.15. Steering system
         3.2.1.16. A forward suspension bracket
         3.2.1.17. Brake system
         3.2.1.18. The electric equipment
         3.2.1.19. The general data
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment



3.2.1.2.9. The tightening moments
THE GENERAL DATA

Bolts of fastening of a head of the block of cylinders (each time new bolts):
  – 1 stage
20 – 30 Nanometers
  – 2 stage
76 – 92 Nanometers
  – 3 stage
To wait 2 minutes
  – 4 stage
To tighten on 90 °
Covers of bearings of a cam-shaft
16 – 22 Nanometers
Covers of radical bearings:
  – 1 stage
20 – 30 Nanometers
  – 2 stage
To tighten on 45 °
Covers of rods:
  – 1 stage
20 – 30 Nanometers
  – 2 stage
To tighten on 60 °
  – 3 stage
To tighten on 20 °
Flywheel:
  – 1 stage
15 – 20 Nanometers
  – 2 stage
To tighten on 45 °
  – 3 stage
To tighten on 45 °
Pulley of an intermediate shaft
40 – 51 Nanometers
Pulley of the fuel pump
20 – 25 Nanometers
The tension device of a gear belt of a drive of the fuel pump
40 – 57 Nanometers
Cam-shaft pulley
  – Bolt М6
8 – 10 Nanometers
  – Bolt М8
27 – 33 Nanometers
The tension device of a gear belt of a drive of a cam-shaft
45 – 55 Nanometers
Intermediate pulley
40 – 51 Nanometers
Casing приводных system belts timing and the fuel pump
8 – 10 Nanometers
Back cover to the block of cylinders
16 – 21 Nanometers
Forward cover to the block of cylinders
20 – 28 Nanometers
The oil pump to the block of cylinders
20 – 25 Nanometers
The basic bearing intermediate валa
8 – 10 Nanometers
Sealant of an intermediate shaft
20 – 25 Nanometers
The oil pallet
6 – 9 Nanometers
Fuel насоc
18 – 22 Nanometers.
Cover of a head of the block of cylinders
3 – 4 Nanometers
Candles накаливания
25 – 30 Nanometers
Atomizers to a head of the block of cylinders
60 – 80 Nanometers
Connections of pipelines of atomizers
15 – 25 Nanometers
Inlet and final collectors to a head of the block of cylinders
10 – 14 Nanometers
Bolts of a final collector
20 – 28 Nanometers