Ford Sierra


Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
    3.1. Cars with petrol engines
   - 3.2. Cars with diesel engines
      - 3.2.1. Changes in a design of the car with 1988 to 1993
         3.2.1.1. The engine 2,3 дм3
          3.2.1.2. The engine 1,8 дм3
          3.2.1.3. Fuel system
          3.2.1.4. The repair which is not demanding removal of the engine
         3.2.1.5. Removal and engine installation
         3.2.1.6. Engine dismantling
         3.2.1.7. Check of details
         3.2.1.8. Check of backlashes of a cranked shaft and rods
         3.2.1.9. Engine assemblage
         3.2.1.10. Greasing system
         3.2.1.11. Cooling system
         3.2.1.12. Coupling
         3.2.1.13. A mechanical five-speed transmission of type МТ 75
         3.2.1.14. A power shaft and the back bridge
         3.2.1.15. Steering system
         3.2.1.16. A forward suspension bracket
         3.2.1.17. Brake system
         3.2.1.18. The electric equipment
         3.2.1.19. The general data
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment



3.2.1.11. Cooling system
THE GENERAL DATA

Cooling system
1 – a radiator,
2 – a casing of the fan of a radiator,
3 – the fan of a radiator,
4 – the case of the thermostat,
5 – the thermostat,
6 – the pump of a cooling liquid,
7 – a broad tank,
8 – the gauge of temperature of a cooling liquid,
9 – a thermoswitch of the fan of a radiator.

THE PUMP OF THE COOLING LIQUID

Removal

PERFORMANCE ORDER
1. To disconnect from the accumulator a weight wire.
2. To merge cooling system (see more low).
3. To remove the air filter.
4. To remove a gear belt of a drive of a cam-shaft (subsection 3.2.1.4.2 see).
5. To remove the bottom casing of a drive of system timing.
6. To remove a roller of the tension device of a gear belt of a drive of system timing.
7. To unscrew a hairpin from the case of the pump of a cooling liquid.
8. To disconnect the elastic pipeline from the pump of a cooling liquid.
9. To remove the pump of a cooling liquid.

Installation

The prevention

In case of replacement of the pump of a cooling liquid it is recommended to establish also a new gear belt of a drive of system timing.

PERFORMANCE ORDER
1. To clear surfaces прилегания linings in the block of cylinders of the engine and the case of the pump of a cooling liquid.
2. To establish a new lining of the pump of a cooling liquid.
3. To screw the pump of a cooling liquid on the block of cylinders, without tightening up to the end fastening bolts.
4. To connect to the pump of a cooling liquid the elastic pipeline of system of cooling. To establish a white sign on the pipeline opposite to a sign on a ledge of the case of the pump.
5. To tighten bolts of fastening of the pump of a cooling liquid the corresponding moment.
6. To screw up on a corresponding place in the case of the pump of a cooling liquid a hairpin, having greased a carving with a small amount of glue Loctite 242.
7. To establish the bottom casing of a drive of system timing.
8. To establish a roller and a spring of the tension device of a gear belt of a drive of system timing. To establish a roller so that its spring has been as much as possible compressed.
9. To establish a gear belt of a drive of system timing (subsection 3.2.1.4.4 see).
10. To establish the air filter.
11. To connect to the accumulator a weight wire.
12. To fill system of cooling and to remove from it air (see more low).
13. To check up tightness of connections.

Plums of system of cooling

The prevention

Cooling liquid is recommended to be changed on the cold engine.

PERFORMANCE ORDER
1. To disconnect from the accumulator a weight wire.
2. Cautiously to unscrew a stopper of a broad tank of system of cooling.
3. To put under a radiator capacity for a following liquid from cooling system.
4. To unscrew a stopper plum on a radiator.
5. To unscrew a stopper plum on the block of cylinders of the engine, located below the vacuum pump.

Filling of system of cooling and removal from it air

PERFORMANCE ORDER
1. To screw up both drain stoppers (in a radiator and in the block of cylinders of the engine).
2. To unscrew a bolt деаэратора the cooling systems, located in the top elastic pipeline of a radiator.
3. To fill in cooling liquid through an aperture in a broad tank while it will not start to follow from under a bolt деаэратора cooling systems.
4. To screw up a bolt деаэратора cooling systems.
5. To fill in cooling liquid to a maximum level corresponding to a sign "MAX" on the case of a tank.
6. Again to fill in cooling liquid in a broad tank to level "MAX".
7. To screw up a stopper of a broad tank.
8. To check up tightness of connections of system of cooling.