Ford Sierra



Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
    3.1. Cars with petrol engines
   - 3.2. Cars with diesel engines
      - 3.2.1. Changes in a design of the car with 1988 to 1993
         3.2.1.1. The engine 2,3 дм3
          3.2.1.2. The engine 1,8 дм3
          3.2.1.3. Fuel system
         - 3.2.1.4. The repair which is not demanding removal of the engine
            3.2.1.4.1. Removal and installation турбокомпрессора
            3.2.1.4.2. Removal of a head of the block of cylinders
            3.2.1.4.3. Repair of a head of the block of cylinders
            3.2.1.4.4. A head of the block of cylinders, system adjustment timing
         3.2.1.5. Removal and engine installation
         3.2.1.6. Engine dismantling
         3.2.1.7. Check of details
         3.2.1.8. Check of backlashes of a cranked shaft and rods
         3.2.1.9. Engine assemblage
         3.2.1.10. Greasing system
         3.2.1.11. Cooling system
         3.2.1.12. Coupling
         3.2.1.13. A mechanical five-speed transmission of type МТ 75
         3.2.1.14. A power shaft and the back bridge
         3.2.1.15. Steering system
         3.2.1.16. A forward suspension bracket
         3.2.1.17. Brake system
         3.2.1.18. The electric equipment
         3.2.1.19. The general data
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment


3.2.1.4.2. Removal of a head of the block of cylinders
THE GENERAL DATA

Head of the block of cylinders


1 – the vortical chamber of combustion,

2 – a lining of a head of the block of cylinders,

3 – an arm with an eye for lifting of the engine,

4 – the gauge of pressure of oil,

5 – a rod of a drive of the vacuum pump,

6 – a head of the block of cylinders,

7 – a lining of a cover of a head of the block of cylinders,

8 – a cover of a head of the block of cylinders
PERFORMANCE ORDER
1. To disconnect from the accumulator a weight wire.
2. To merge cooling system (subsection 3.2.1.11 see).
3. To disconnect the pipeline of giving of air to турбокомпрессору, the elastic pipeline of system of ventilation картера the engine from a cover of a head of the block of cylinders and the pipeline of giving of air between the air filter and a radiator casing (the pipeline is put on on the union).
4. To disconnect from a head of the block of cylinders all elastic pipelines of system of cooling.
5. To disconnect the vacuum pipeline of the amplifier of brakes and the pipeline of return of oil from the vacuum pump.
6. To disconnect electric wires from свеч накаливания, the gauge of pressure of oil, the gauge of temperature of a cooling liquid and a thermoswitch of the fan of a radiator.
7. To disconnect from atomizers pipelines of return of fuel.
8. To disconnect pipelines of injection from the fuel pump and atomizers.
9. To disconnect a cover of the thermostat from a head of the block of cylinders.
10. To disconnect топливопроводы from the pump and the fuel filter.
11. To disconnect the vacuum pipeline from an inlet collector.
12. To disconnect маслопроводы from турбокомпрессора and the oil pump.
13. To disconnect турбокомпрессор from a final collector.
14. To disconnect скобу, supporting forward exhaust pipe from a transmission cross-beam.
15. To disconnect returnable маслопровод from турбокомпрессора and the block of cylinders of the engine.
16. To remove клиновые приводные belts of the pump of a cooling liquid and the generator.
17. To unscrew a bolt of fastening on the left side of the bottom casing of a drive of system timing.
18. To unscrew a bolt of fastening of the top casing of a drive of system timing on the right side that he could be taken.
19. To remove three spring hooks of the top casing of a drive of system timing, to take bolts of fastening and to lower a casing downwards.
20. To take from the block of cylinders, at height of a pulley of a cranked shaft, a stopper of a control aperture send for installation of a cranked shaft.
21. To turn a cranked shaft so that cut of a pulley of the fuel pump there were in a position "12 hours".
22. To establish in the block of cylinders the mandrel (1) for installation of a cranked shaft in position ВМТ of the piston 1. The cylinder.
23. To rotate a cranked shaft counter-clockwise to its emphasis in the mandrel.
24. To remove a roller of the tension device of a gear belt of a drive of system timing, and then a gear belt.
25. To remove a passive pulley (increasing corner of coverage of a gear belt) and a back casing of a drive of system timing.
26. To unscrew atomizers.
27. To uncover heads of the block of cylinders.
28. To unscrew ten bolts of fastening of a head of the block of cylinders in sequence of return to their tightening (cм. Fig. Sequence of a tightening of bolts of a head of the block of cylinders).
29. To remove a head of the block of cylinders.