Ford Sierra

Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
   - 3.1. Cars with petrol engines
      3.1.1. Weights and transfer numbers
      3.1.2. Operational liquids
      - 3.1.3. Changes in a design of the car with 1984 to 1986
         3.1.3.1. The engine
         3.1.3.2. A head of the block of cylinders
         3.1.3.3. The block of cylinders of the engine
         3.1.3.4. The Krivoshipno-shatunnyj mechanism
         3.1.3.5. A cranked shaft
         3.1.3.6. System timing
         3.1.3.7. An engine mount
         3.1.3.8. Cooling system
         - 3.1.3.9. The carburettor
            3.1.3.9.1. Carburettor Ford with we change section диффузора
            3.1.3.9.2. Carburettors Weber
            3.1.3.9.3. Carburettor Pierburg
         3.1.3.10. System of injection of fuel
         3.1.3.11. Ignition system
         3.1.3.12. Coupling
         3.1.3.13. A mechanical four-speed transmission
         3.1.3.14. A mechanical five-speed transmission
          3.1.3.15. Automatic transmission Ford A 4 LD
         3.1.3.16. A power shaft and the back bridge
         3.1.3.17. System of a steering with the hydraulic booster
         3.1.3.18. A forward suspension bracket
         3.1.3.19. A back suspension bracket
         3.1.3.20. Brake system
          3.1.3.21. The electric equipment
         3.1.3.22. The general data
       3.1.4. Changes in a design of the car with 1987 to 1989
       3.1.5. Changes in a design of the car with 1990 till February, 1993
    3.2. Cars with diesel engines
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment

3.1.3.9. The carburettor

3.1.3.9.1. Carburettor Ford with we change section диффузора

THE GENERAL DATA

THE NEEDLE VALVE

Since May, 1983 (the code of date of manufacturing "DL") is entered new type of the needle valve operating giving of fuel to поплавковой to the chamber, and also a new clip of the needle valve.

In case of repeating stops of the engine directly after its start it is necessary to uncover the carburettor and if in поплавковой to the chamber there is no fuel it is necessary to arrive as follows.

PERFORMANCE ORDER

1. To take an axis of a float and a clip of the needle valve (if was present at the given type), paying attention, that both these of an element have not fallen inside поплавковой chambers.

2. To take the needle valve (is not subject to repeated installation).

The prevention
It is impossible to unscrew bolts of fastening of the elements which are dosing out fuel, with a view of simplification of access to a float.

3. To establish the new needle valve and a new clip, paying attention to correct placing of a clip in the flute of the valve provided for it.

4. To insert a float, paying attention to correct position of a remote lining between the holder of the lever and the needle valve, and to insert an axis into cut of the holder of a float.

5. Some times to move a float, checking possibility of its free rotation on an axis.

6. To establish a new lining of a cover поплавковой chambers and to tighten bolts of fastening of a cover of the carburettor the moment of 2,5 Nanometers.

The prevention
Carburettors with changeable section of a mouth in a manufacturing initial stage have not been equipped by a clip of fastening of the needle valve.

MANAGEMENT THROTTLE ЗАСЛОНКОЙ

The lever throttle заслонки carburettor Ford

And – the lever throttle заслонки,

In – a core from an artificial material

Since January, 1985 (the code of date of manufacturing "FJ") is changed the lever () throttle заслонки, a core () from an artificial material. At infringement of working capacity of the mechanism of management throttle заслонкой the old type caused by deterioration of a core () from an artificial material, it is necessary to establish the lever and a core of new type.
The prevention
There are two types of levers throttle заслонки mixes – with cut for a core direct or bent. It is necessary to use necessarily the lever with cut of the same form, as well as in a factory complete set.