Ford Sierra

Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
   - 3.1. Cars with petrol engines
      3.1.1. Weights and transfer numbers
      3.1.2. Operational liquids
      - 3.1.3. Changes in a design of the car with 1984 to 1986
         3.1.3.1. The engine
         3.1.3.2. A head of the block of cylinders
         3.1.3.3. The block of cylinders of the engine
         3.1.3.4. The Krivoshipno-shatunnyj mechanism
         3.1.3.5. A cranked shaft
         3.1.3.6. System timing
         3.1.3.7. An engine mount
         3.1.3.8. Cooling system
          3.1.3.9. The carburettor
         3.1.3.10. System of injection of fuel
         3.1.3.11. Ignition system
         3.1.3.12. Coupling
         3.1.3.13. A mechanical four-speed transmission
         3.1.3.14. A mechanical five-speed transmission
          3.1.3.15. Automatic transmission Ford A 4 LD
         3.1.3.16. A power shaft and the back bridge
         3.1.3.17. System of a steering with the hydraulic booster
         3.1.3.18. A forward suspension bracket
         3.1.3.19. A back suspension bracket
         3.1.3.20. Brake system
         - 3.1.3.21. The electric equipment
            3.1.3.21.1. Inclusion of headlights
            3.1.3.21.2. A bolt of fastening of the holder of the generator
            3.1.3.21.3. Safety locks and the relay
            3.1.3.21.4. A contour of an electric food (1985-1986)
            3.1.3.21.5. A gymnastics and start contour (1985-1986)
            3.1.3.21.6. A contour of management of engine OHC 1,8 дм3 (1985-1986)
            3.1.3.21.7. A contour of management of engine OHC 2,0 дм3 (1985-1986)
            3.1.3.21.8. A contour of management of injection of fuel of engine OHC 2,0 дм3
         3.1.3.22. The general data
       3.1.4. Changes in a design of the car with 1987 to 1989
       3.1.5. Changes in a design of the car with 1990 till February, 1993
    3.2. Cars with diesel engines
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment

3.1.3.21. The electric equipment

3.1.3.21.1. Inclusion of headlights

THE GENERAL DATA

The location of the relay of light of headlights in the block of safety locks and the relay

The crosspiece established in a position "IV" in the block of safety locks and the relay if the car is not equipped by the relay of light of headlights

Changes in a way of connection of a plait of electric wires to the block of safety locks and the relay

And – connection (in addition soldered) wire of golden colour,
In – connection of an additional brown wire of weight,
With – connection of an original yellow wire (from a safety lock),
D – connection to weight of a brown wire

Since February, 1983 (a code of date of manufacturing "DК") cars of versions: the basic (Base), L and GL are equipped with the relay of inclusion of light of headlights which is located in a position of "IV" relay in the block of safety locks and the relay (fig. the Location of the relay of light of headlights in the block of safety locks and the relay see).

In case of wrong inclusion of headlights of a passing light in the cars made before introduction of this relay, it is necessary to arrive as follows.

PERFORMANCE ORDER

Cars with a crosspiece in a position of "IV" relay in the block of safety locks and the relay

1. To check up a plait of wires from headlights of near and far light.

2. If malfunction is not eliminated, it is necessary to remove a crosspiece (fig. a Crosspiece established in a position "IV" in the block of safety locks and the relay if the car is not equipped by the relay of light of headlights see) and into positions "IV" to insert the relay (fig. the Location of the relay of light of headlights in the block of safety locks and the relay see).

Cars without a crosspiece and without the relay in a position of "IV" relay in the block of safety locks and the relay

3. To check up a plait of wires from headlights of near and far light.

4. If malfunction is not defined, to disconnect the accumulator.

5. To remove an internal upholstery on the left side under the forward panel.

6. To extend a plate with sockets of the block of safety locks and the relay towards an engine compartment.

7. To cut on distance about 160 mm a wire of the yellow colour going from safety lock N16 or 17.

8. To solder a socket (N А83SX-14489-AA) on the end of the wire going from a safety lock № 16 or 17, and to isolate this socket.

9. To prepare two pieces of wires of brown and yellow colours section 1,5 мм2 and length 160 mm.

10. To solder flat standard contact on the end of a wire of brown colour and a socket (N А83SX-14489-AA) on its other end and to isolate them.

11. To solder a socket (N А83SX-14489-AA) on the end of a yellow wire. Other end of this wire to solder to the end of a yellow wire (remained after cutting) from an original plait and to isolate connections.

12. To connect the end of a yellow wire from safety lock N16 or 17 to a socket () (fig. of Change in a way of connection of a plait of electric wires to the block of safety locks and the relay see) in a position of "IV" relay.

13. Additional wires to connect according to fig. of Change in a way of connection of a plait of electric wires to the block of safety locks and the relay – brown in points () and (D), and yellow in a point ().