Ford Sierra


Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
   - 3.1. Cars with petrol engines
      3.1.1. Weights and transfer numbers
      3.1.2. Operational liquids
       3.1.3. Changes in a design of the car with 1984 to 1986
      - 3.1.4. Changes in a design of the car with 1987 to 1989
         3.1.4.1. Engine OHC
          3.1.4.2. Engine CVH 1,8 дм3
          3.1.4.3. Engine DOHC
          3.1.4.4. Service and repair
          3.1.4.5. Coupling
         3.1.4.6. A mechanical five-speed transmission of type
          3.1.4.7. A mechanical five-speed transmission of type МТ 75
         3.1.4.8. An automatic transmission
         3.1.4.9. A forward suspension bracket
         - 3.1.4.10. Brake system
            3.1.4.10.1. Technical characteristics
            3.1.4.10.2. Service and repair
            3.1.4.10.3. Adjustment of a manual brake
            3.1.4.10.4. Removal of air from brake system
            3.1.4.10.5. Antiblocking system
            3.1.4.10.6. Check of functioning ABS
            3.1.4.10.7. Hydraulic knot of management
            3.1.4.10.8. The gauge of speed of rotation of wheels
          3.1.4.11. The electric equipment
         3.1.4.12. The general data
       3.1.5. Changes in a design of the car with 1990 till February, 1993
    3.2. Cars with diesel engines
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment





3.1.4.10.8. The gauge of speed of rotation of wheels

Replacement of the gauge of speed of rotation of a forward wheel

PERFORMANCE ORDER
1. To weaken nuts of fastening of a corresponding forward wheel.
2. To lift the car and to remove a wheel.
3. To unscrew bolts of fastening of the gauge of rotation.
4. To disconnect from the rotation gauge an electric socket.
5. To take the gauge.
6. To unhook a wire of the gauge from spring скоб.
7. To clear a nest of fastening of the gauge of speed of rotation of a wheel of a dirt, rust traces etc.
8. Slightly to grease a nest of fastening of the gauge with greasing for bearings.
9. To establish a new sealing ring of round section on the gauge.
10. To establish the gauge of speed of rotation in its nest.
11. To tighten a bolt of fastening of the gauge.
12. To connect to the gauge an electric socket and to hook on an electric wire in spring скобах.
13. To establish a wheel and to lower the car.
14. To tighten nuts of fastening of a wheel the corresponding moment.

Replacement of the gauge of speed of rotation of a back wheel

The prevention

The brake liquid is in a contour of back brakes under a high pressure. It is not necessary to press a brake pedal.

PERFORMANCE ORDER
1. To weaken nuts of fastening of a corresponding back wheel.
2. To lift the car and to remove a wheel.
3. To release the lever of a manual brake.
4. To lift back sitting and to reject a floor covering forward.
5. To take a wire from скобы and to disconnect an electric socket from the gauge of speed of rotation of a wheel.
6. To disconnect a cable of a manual brake from скобы on the lever of a back suspension bracket.
7. To take a forward bolt of fastening of a brake support.
8. To turn a support upwards.
9. To unscrew a bolt of fastening of the gauge and to take it.
10. To clear a nest of fastening of the gauge of speed of rotation of a wheel of a dirt, rust traces etc.
11. Slightly to grease a nest of fastening of the gauge with greasing for bearings.
12. To establish a new sealing ring of round section on the gauge.
13. To execute the same initial actions which are resulted at installation of the gauge of speed of rotation of a forward wheel, and then to execute in return sequence the actions resulted at removal of the gauge of speed of rotation of a back wheel.

Other information, concerning a technical characteristics, adjustment and repair of brake system is resulted in разделе10 and in subsection 3.1.3.20.