Ford Sierra



Ford Sierra
1.2. Car identification
2. Maintenance service
- 3. The general data
   - 3.1. Cars with petrol engines
      3.1.1. Weights and transfer numbers
      3.1.2. Operational liquids
       3.1.3. Changes in a design of the car with 1984 to 1986
      - 3.1.4. Changes in a design of the car with 1987 to 1989
         3.1.4.1. Engine OHC
         - 3.1.4.2. Engine CVH 1,8 дм3
             3.1.4.2.1. Technical characteristics
            3.1.4.2.2. Engine adjustment
            3.1.4.2.3. Ignition system
            3.1.4.2.4. System timing
            3.1.4.2.5. Assemblage of engine CVH 1,8 дм3
          3.1.4.3. Engine DOHC
          3.1.4.4. Service and repair
          3.1.4.5. Coupling
         3.1.4.6. A mechanical five-speed transmission of type
          3.1.4.7. A mechanical five-speed transmission of type МТ 75
         3.1.4.8. An automatic transmission
         3.1.4.9. A forward suspension bracket
          3.1.4.10. Brake system
          3.1.4.11. The electric equipment
         3.1.4.12. The general data
       3.1.5. Changes in a design of the car with 1990 till February, 1993
    3.2. Cars with diesel engines
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment


3.1.4.2.5. Assemblage of engine CVH 1,8 дм3
THE GENERAL DATA

The prevention

The difference in comparison with engine ONS is resulted only.


The krivoshipno-shatunnyj mechanism of engine CVH

1 – the piston with a finger and piston rings,
2 – a rod,
3 – шатунные loose leaves,
4 – loose leaves of radical bearings,
5 – persistent half rings of a cranked shaft,
6 – a cranked shaft,
7 – a back sealing ring of a cranked shaft,
8 – a forward sealing ring of a cranked shaft

System of greasing of engine CVH

1 – the oil filter,
2 – indexes of level of oil (with the alarm system
And without the level alarm system),
3 – directing the index of level of oil,
4 – the gauge of pressure of oil,
5 – the oil pump,
6 – the pipeline of return of oil,
7 – a lining,
8 – the pipeline of giving of oil to the pump,
9 – a lining

After extraction of halves of loose leaves of radical bearings and persistent half rings of a cranked shaft it is necessary to take from ventilation system картера an oil separator together with its spring.

Removal of a separator of oil from ventilation system картера engine CVH


Removal and installation of the oil pump

PERFORMANCE ORDER
1. To merge oil from the oil pallet.
2. To remove a casing of a drive of system timing and a gear belt.
3. To remove from a cranked shaft клиновой a pulley, a pulley and the oil pallet.
4. To unscrew bolts of fastening of the oil pump and to remove the pump.
5. To wash up the oil pallet and the mesh oil filter, and then to execute actions in return sequence in relation to removal process.
6. To put on a gear belt, paying attention to coincidence of signs on a cranked shaft and a cam-shaft.

Removal of the pump of a cooling liquid

PERFORMANCE ORDER
1. To disconnect from the accumulator a wire of weight and to merge a liquid from cooling system.
2. To remove клиновой a belt of a drive of the generator.
3. To rotate a cranked shaft before coincidence of adjusting signs ВМТ of the piston of 1st cylinder on a pulley of a cranked shaft and a casing of a drive of system timing, and then to remove a casing of a drive of system timing.
4. To weaken the tension device and to remove a gear belt.
5. To disconnect the elastic pipeline of a cooling liquid going to a radiator, and the pipeline of a cooling liquid going to a contour of heating of salon of the car.
6. To remove the tension device of a gear belt.
7. To unscrew four bolts of fastening of the pump of a cooling liquid to the block of cylinders of the engine and to take the pump of a cooling liquid.

Installation of the pump of a cooling liquid

PERFORMANCE ORDER
1. To clear a surface прилегания linings on the pump of a cooling liquid and the block of cylinders of the engine.
2. To establish a new lining and to screw the pump of a cooling liquid on the block of cylinders of the engine.
3. To establish the tension device of a gear belt.
4. To put on a gear belt.
5. To establish a casing of a drive of system timing.
6. To put on клиновой a belt of a drive of the generator and to pull it.
7. To connect elastic the pipeline of system of cooling, to fill system of cooling and to check up its tightness.

Other information, concerning a technical characteristics, adjustment and engine repair, is in subsection 2.1 and in subsection 3.1.3.1.