Ford Sierra
1.2. Car identification
2. Maintenance service
3. The general data
- 4. Engines
4.1. Petrol engines
- 4.2. The diesel engine
4.2.1. Technical characteristics
4.2.2. Check and adjustment of backlashes of valves
4.2.3. Fuel system
4.2.4. Atomizers
4.2.5. Candles накаливания
4.2.6. Compression check
4.2.7. Removal of air from fuel system
4.2.8. The fuel filter
4.2.9. The fuel pump, installation of the beginning of injection of fuel
4.2.10. Adjustment of number of turns of idling
- 4.2.11. The repair which is not demanding removal of the engine
4.2.11.1. A head of the block of cylinders
4.2.11.2. Removal and engine installation
- 4.2.11.3. Dismantling, repair and engine assemblage
4.2.11.3.1. Installation of the back radical bearing
4.2.11.3.2. Assemblage of knot the piston-rod
4.2.11.3.3. Assemblage of a drive of system timing
4.2.11.3.4. The further assemblage of the engine
4.2.11.4. Greasing system
4.2.11.5. Cooling system
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment
|
Installation of a persistent half ring of a cranked shaft
| PERFORMANCE ORDER |
| 1. To establish a lining in a flute in the block of cylinders and a cover of the back radical bearing. |
| |
2. To establish a core of the special adaptation (21.085) on a lining. |
| 3. To strike a wooden hammer on a flat surface of the special adaptation so that a lining in appropriate way has filled the flute provided for it and was not exposed to deformation. To level the ends of a lining with a plane of the block of cylinders and covers, over this plane elements of a material of a lining should not act. To grease with engine oil loose leaves with oil flutes and to lay them in nests of the block of cylinders, paying attention, that they were in the same nests in which stood earlier (to observe the executed designations). |
| 4. Cautiously to establish a cranked shaft on loose leaves of radical bearings. |
|
5. To establish covers of radical bearings № 2, 3, 4 and 5, and also preliminary, without lateral sealants, a bearing cover № 1. To tighten bolts of covers of radical bearings the moment of 110 Nanometers. |
6. To arrange the indicator of hour type so that its measuring tip concerned a forward part of a cranked shaft.
To check up an axial backlash of a cranked shaft which should make 0,08–0,29 mm. |
| 7. In case of inappropriate value of an axial backlash it is necessary to replace persistent half rings of a cranked shaft. For a choice there are two thickness: 2,30 and 2,50 mm. |
|
Installation of lateral sealants in a cover of the back radical bearing
| PERFORMANCE ORDER |
| 1. To unscrew a cover of the back radical bearing (№1) cranked shaft. |
| 2. To put on lateral уплотнители a cover of the back radical bearing, holding them by means of the adaptation 21.085 and to attach a cover to the adaptation. |
| 3. To grease with engine oil of a surface of lateral sealants and all knot to press to the block of cylinders. To insert bolts of a cover of the back radical bearing and to tighten their moment 110Нм. |
| 4. Whether to check up freely the cranked shaft in bearings rotates. |
| 5. To cut off the ends of lateral sealants so that they supported the bottom plane of the block of cylinders on 0,5 mm. To use thus a metal lath in the thickness of 0,5 mm, available in the complete set of the special adaptation. |
|
|
|