Ford Sierra



Ford Sierra
1.2. Car identification
2. Maintenance service
3. The general data
- 4. Engines
    4.1. Petrol engines
   - 4.2. The diesel engine
       4.2.1. Technical characteristics
      4.2.2. Check and adjustment of backlashes of valves
       4.2.3. Fuel system
       4.2.4. Atomizers
      4.2.5. Candles накаливания
      4.2.6. Compression check
      4.2.7. Removal of air from fuel system
      4.2.8. The fuel filter
      4.2.9. The fuel pump, installation of the beginning of injection of fuel
      4.2.10. Adjustment of number of turns of idling
      - 4.2.11. The repair which is not demanding removal of the engine
          4.2.11.1. A head of the block of cylinders
         4.2.11.2. Removal and engine installation
         - 4.2.11.3. Dismantling, repair and engine assemblage
            4.2.11.3.1. Installation of the back radical bearing
            4.2.11.3.2. Assemblage of knot the piston-rod
            4.2.11.3.3. Assemblage of a drive of system timing
            4.2.11.3.4. The further assemblage of the engine
          4.2.11.4. Greasing system
          4.2.11.5. Cooling system
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment



4.2.11.3. Dismantling, repair and engine assemblage Dismantling

PERFORMANCE ORDER
1. To fix the engine on a corresponding bed, to merge oil and to remove the oil filter. To remove the vacuum pump and клиновой a drive belt; to unscrew the vacuum pipeline.
2. To remove completely the generator (together with the holder) and приводные клиновые belts, a roller of the tension device клинового a belt of the pump of a cooling liquid and a belt.
3. To unscrew from a head of the block of cylinders the thermostat of a regulator of the increased number of turns of idling, then to unscrew returnable fuel hoses and to remove the fuel pump.
4. To unscrew and remove fuel pipelines. To muffle corresponding stoppers of an aperture of pipelines and adaptations of fuel system, not to admit hit there a dust.
5. To take atomizers, their linings and a thermoisolation ring, to disconnect an electric wire and токовую the tyre from свеч накаливания and to unscrew them.
6. To disconnect the pipeline of giving of oil to an axis of the lever of valves and to unscrew external holders of an axis of the lever of valves.
7. To unscrew bolts of fastening of a head of the block of cylinders (in return sequence in relation to their tightening) and to remove a head and its lining.
8. To remove держател ь the oil filter and an oil radiator, and then to unscrew the fuel pump with its holder. To remove pulleys of a cranked shaft and the fan, to remove a casing of a chain of system timing.
9. To block a screw-driver the tension device of a chain, to remove the device and its clown, to take a system chain timing and an asterisk of the fuel pump.
10. To remove a flange of fastening of a drive of the fuel pump and the pipeline of giving of oil.
11. To pull together an asterisk from a cranked shaft and to remove the tension device приводной system chains timing.
12. To remove from a flywheel a leading part and a coupling disk, the oil pallet, a stopper of the oil pump, a nut and a bolt of fastening of the oil pump, and then to remove the oil pump.
13. To turn двигате ль on 180 , to remove from the block of cylinders an intermediate plate, to take a cam-shaft, and then by means of a stripper to remove an asterisk from a cam-shaft.
14. To take pushers and to establish them in sequence with which they occupy in the engine.
15. To designate covers of radical bearings, and also rods and their covers (from outside the fuel pump).
16. To remove covers of radical bearings and a cover of rods.
17. To take a cranked shaft from the block of cylinders of the engine.
18. To take from cylinders pistons together with rods.
19. To establish loose leaves together with covers in sequence with which they occupied in the engine.

Assemblage


The prevention

Before engine assemblage to check up all details and to establish only pure and in a good technical condition.

To observe: demanded communications of co-operating details, a correct relative positioning of these details and their correct installation according to their designations.


PERFORMANCE ORDER
1. To replace all linings and the spring washers protecting bolts from unscrewing.
2. To clear co-operating surfaces of linings and connected details. For clearing not to use abrasive materials and sharp adaptations. These surfaces cannot carry traces of blows, attritions or scratches.
3. Apertures of oil channels in the block of cylinders of the engine should be muffled the copper stoppers covered герметизирующей with paste Loctite Frenetanch.