Ford Sierra

Ford Sierra
1.2. Car identification
2. Maintenance service
3. The general data
- 4. Engines
   - 4.1. Petrol engines
      - 4.1.1. Technical characteristics
         4.1.1.1. A head of the block of cylinders
         4.1.1.2. The block of cylinders of the engine
         4.1.1.3. The Krivoshipno-shatunnyj mechanism
         4.1.1.4. System timing
         4.1.1.5. Greasing system
         4.1.1.6. Cooling system
         4.1.1.7. Fuel system
         4.1.1.8. Ignition system
         4.1.1.9. The tightening moments
      4.1.2. Adjustment of backlashes of valves
       4.1.3. Ignition system
       4.1.4. Fuel system
       4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and engine installation
      4.1.7. Engine dismantling
      4.1.8. Identification of co-operating parts
      4.1.9. Engine assemblage
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. System timing
      4.1.13. Greasing system
       4.1.14. Cooling system
      4.1.15. A suspension bracket of the power unit
      4.1.16. System of release of the fulfilled gases
    4.2. The diesel engine
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
10. Brake system
11. A body
12. An electric equipment

4.1.1.9. The tightening moments

THE GENERAL DATA

Bolts of covers of radical bearings
88 – 102 Nanometers

Bolts of rods
40 – 47 Nanometers

Bolt of a pulley of a cranked shaft
55 – 60 Nanometers

Bolt of a gear wheel of a cam-shaft
45 – 50 Nanometers

Flywheel bolts
67 – 70 Nanometers

Bolts of fastening of the oil pump
17 – 21 Nanometers

Bolts of a cover of the oil pump
9 – 13 Nanometers

Bolts of the oil pallet (a tightening order – look subsection 4.1.9)

  – 1st stage
1 – 2 Nanometers

  – 2nd stage
6 – 8 Nanometers

  – 3rd stage (after 20 minutes of work of the engine)
8 – 10 Nanometers

Stopper oil plum in the oil pallet
21 – 28 Nanometers

The gauge of pressure of oil
12 – 15 Nanometers

Bolts of adjustment of a backlash of valves about levers of valves
50 – 55 Nanometers

Bolts of a head of the block of cylinders (the tightening order – see in subsection 4.1.5.4)

  – 1st stage
40 – 45 Nanometers

  – 2nd stage
50 – 70 Nanometers;

  – 3rd stage (later 10 – 20 mines)
73 – 83 Nanometers

  – 4th stage (after 15 minutes of work of the engine at number of turns of 1000 rpm; at the hot engine)
95 – 115 Nanometers

System casing timing
13 – 17 Nanometers

Inlet collector
17 – 21 Nanometers

Final collector
21 – 25 Nanometers

Spark plugs
20 – 28 Nanometers

The thermostat case
17 – 21 Nanometers

Bolts of a cover of a head of the block of cylinders (the tightening order – see in subsection 4.1.5.4)

  – Bolts 1 – 6 and 9, 10
5 – 7 Nanometers

  – Bolts 7 and 8
2 – 2,5 Nanometers