Ford Sierra



Ford Sierra
1.2. Car identification
2. Maintenance service
3. The general data
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
- 9. Suspension brackets
    9.1. A forward suspension bracket
   - 9.2. A back suspension bracket
      9.2.1. Technical characteristics
      9.2.2. Shock-absorber replacement
      9.2.3. Replacement of a spring of a suspension bracket
      9.2.4. Removal and installation of the lever of a suspension bracket
      9.2.5. Replacement of the metallo-rubber plug of a beam of a suspension bracket
      9.2.6. Replacement of bearings of a nave of a back wheel
10. Brake system
11. A body
12. An electric equipment


9.2.3. Replacement of a spring of a suspension bracket
THE GENERAL DATA

Removal of a spring of a back suspension bracket

1 – скобы fastenings of brake hoses,

2 – the bottom fastening of the shock-absorber,

3 – fastening of a beam of a back axis to a body,

4 – an axis of rotation of the lever

Removal

PERFORMANCE ORDER
1. To remove a protective cap of a back wheel and to weaken nuts of fastening of a wheel.
2. To lift and fix a back part of the car, to remove a corresponding back wheel.
3. To remove a brake drum (subsection 10.3 see).
4. A nakidnym key to unscrew four bolts of fastening of the case (5, fig. the Back suspension bracket see) bearings of a nave of a wheel, rotating a nave of a back wheel so that its apertures have settled down on continuation of an axis of separate bolts of fastening of the case of bearings of a nave.
5. To remove from within a bearing brake disk a plastic casing external приводного the hinge of a semiaxis after a raising a screw-driver of tightening rings on heads of bolts and unscrewing of bolts of fastening of a casing.
6. To take полуось entirely through bearing board of a back brake, directing it directly and holding so that it did not overhang downwards.
7. To take an U-shaped clamp and to remove a brake hose (without disconnecting it) from the holder under the bottom about a wheel.
8. To establish a jack under the lever of a suspension bracket and to lift the lever so that all loading had on a suspension bracket spring.
9. To unscrew the bottom fastening of the shock-absorber (a berlin body) or to remove the shock-absorber (a body комби).
10. To unscrew from the corresponding party bolts of fastening of a beam of a back axis to a body after bending back of a safety lining and unscrewing of a bolt of fastening of the metallo-rubber plug (8, fig. the Back suspension bracket see), and also two bolts of fastening of this plug to a body.
11. Cautiously to lower the lever downwards.
12. To take a suspension bracket spring together with a rubber basic cup.

Installation

PERFORMANCE ORDER
1. To establish a spring together with a rubber basic cup on a shoulder of the lever of a suspension bracket.
2. To lift a jack to put a spring on a corresponding place.

The prevention

In cars with a body комби simultaneously with a spring it is necessary to establish the shock-absorber.


3. To attach the metallo-rubber plug of a beam of a back axis to a body, having tightened bolts of its fastening by the corresponding moments.
4. To establish the bottom fastening of the shock-absorber (in cars with a body комби), and also connection of a brake hose on the holder of a body and to fix it.
5. To take a jack.
6. To establish полуось with a wheel nave. To attach a nave of a wheel four new bolts to the suspension bracket lever, tightening their corresponding moment.
7. To establish from within a bearing brake board a plastic casing external приводного the semiaxis hinge.
8. To establish a brake drum.
9. To establish a wheel, to screw up nuts of fastening of a wheel, to lower the car and to tighten nuts of fastening of a wheel the corresponding moment.