Ford Sierra

10.3.2. Replacement brake колодок

THE GENERAL DATA

The scheme of functioning of the mechanism of automatic adjustment of a backlash brake колодок back brake Gerling

And – normal position, In – position of braking, 1 – brake колодка, 2 – the lever of a gear plate,

3 – a backlash, 4 – a connector of management, 5 – managements, 6 – a bearing brake board

---

The prevention

Brake overlays are pasted to brake колодкам. New synchronous колодка (lobby) has an overlay a bit more thickly, than asynchronous колодка (back). The forward brake overlay wears out faster and boundary deterioration both колодки reach almost simultaneously.

---

Removal

PERFORMANCE ORDER

1. To weaken nuts of fastening of back wheels. 2. To lift and fix a back part of the car, to remove a back wheel. 3. To remove a brake drum. 4. To remove a conductor of a lobby brake колодки (synchronous), дожимая flat-nose pliers a cup to a conductor spring колодки and turning it on 90 ° at simultaneous keeping behind a conductor core, to remove a cup with a spring and to take a conductor core колодки. Berlin 2,0 дм3 and комби 5. To delay a lobby brake колодку from a bearing brake board, simultaneously turning the top end колодки outside. 6. To unhook the top and bottom returnable spring from a lobby колодки. 7. To remove a lobby brake колодку (synchronous). Berlin 1,3 and 1,6 дм3 8. To lift a lobby brake колодку from a support below, by means of a screw-driver rested against a support, to remove the end колодки from a support, to move it in a direction back колодки and to unhook the bottom returnable spring. 9. To delay a lobby колодку above from the cylinder and to move it about the cylinder in a direction back колодки not to damage a rubber casing of the cylinder. 10. To unhook the top returnable spring with the help пассатижей, inserted into an aperture of a flange of a nave of the wheel, established over the top returnable spring after corresponding rotation of a flange of a nave. 11. To incline forward upwards the bottom part of a lobby brake колодки to a detachment of the lever of adjustment of a backlash from a latch. 12. To disconnect a lobby brake колодку from a press core. All types 13. To remove a cup, a spring and a conductor back brake колодки (asynchronous), it is similar as well as a lobby conductor колодки. 14. To remove back brake колодку with the lever of a manual brake and to unhook a cable of a manual brake. 15. To disconnect the lever of automatic adjustment of a backlash together with a spring from back brake колодки (asynchronous).

Installation

PERFORMANCE ORDER

1. To check up and clear details and bearing brake board (it is possible to wash out it spirit). 2. To put a little special greasing Wolfracote on six elements of a bearing brake board. 3. To connect the lever of automatic adjustment of a backlash together with a spring and a cable of a manual brake with back brake колодкой (asynchronous). 4. To insert back колодку (asynchronous), опирая its ends into the piston and a support in the bottom part of a bearing brake board. 5. To establish a conductor back brake колодки (asynchronous). Berlin 2,0 дм3 and комби 6. To hook on returnable springs (top and bottom) for a lobby brake колодку (synchronous), keeping колодку it is perpendicular to a bearing brake board. 7. To establish the bottom end of a lobby brake колодки (synchronous) in a support in the bottom of a bearing brake board, and the top end of this колодки in a piston groove. 8. To press a lobby колодку to a bearing brake board. 9. To establish a conductor of a lobby brake колодки (synchronous). Berlin 1,3 and 1,6 дм3 10. To connect the lever of adjustment of a backlash to a latch and to fasten the top returnable spring to a lobby колодке (synchronous). 11. To press a latch downwards and to incline a lobby brake колодку upwards to disconnect the lever of adjustment of a backlash. 12. To connect the lever of adjustment of a backlash to a press core. 13. To incline a lobby brake колодку (synchronous) downwards and again to connect the lever of adjustment of a backlash to a latch. 14. To establish a lobby brake колодку (synchronous) near to a support in the bottom part of a bearing brake board and to insert the bottom returnable spring. 15. To pick up a lobby brake колодку (synchronous) a screw-driver and to establish it on a support. 16. To pull forward the top part of a lobby колодки (synchronous) before its fixing by the adjusting lever. 17. To press a lobby brake колодку (synchronous) to a bearing brake board and to fix the end колодки in a groove of the piston after easing by a screw-driver of a latch before combination of an aperture of a conductor in колодке with a conductor aperture in bearing brake шите. 18. To establish a conductor of a lobby brake колодки (synchronous). All types 19. To establish the mechanism of automatic adjustment of a backlash колодок so that to remove back brake колодки. 20. To establish a brake drum. 21. To press a brake pedal some times that the adjustment mechanism has earned. 22. To establish back wheels and to screw up nuts of fastening of wheels. 23. To lower the car and to tighten nuts of fastening of wheels the corresponding moment.