Ford Sierra



Ford Sierra
1.2. Car identification
2. Maintenance service
3. The general data
4. Engines
5. Coupling
6. Transmissions
7. A kardannyj shaft and the back bridge
8. A steering
9. Suspension brackets
- 10. Brake system
   10.1. Technical characteristics
   - 10.2. Forward brakes
      10.2.1. Replacement brake колодок
      10.2.2. Support replacement
      10.2.3. Replacement of a brake disk
      10.2.4. Support repair
    10.3. Back brakes
   10.4. Removal and installation of the main brake cylinder
   10.5. Removal of air from brake system
   10.6. Adjustment of a manual brake
11. A body
12. An electric equipment


where to buy viagra without a prescription

10.2. Forward brakes

10.2.1. Replacement brake колодок
THE GENERAL DATA

Forward brake

And – cars with engines 1,3 and 1,6 дм3,

In – cars with the engine 2,0 дм3,

1 – an arm of a support,

2 – a support,

3 – brake колодки,

4 – the piston,

5 – a brake disk


CARS WITH ENGINES 1,3 AND 1,6 ДМ3
The prevention

Simultaneous replacement of all brake колодок forward brakes if at least one of them wears out till the minimum thickness is recommended.


Replacement

PERFORMANCE ORDER
1. To weaken nuts of fastening of forward wheels.
2. To lift and fix in front of the car, to remove forward wheels.
3. To unscrew in the top part of a support a bolt of fastening of a support of a brake to the holder, holding with a flat key the top directing finger.
4. To take a bolt of fastening of a support of a brake to the holder.

The prevention

In cars with engines 2,0 дм3 it is necessary to unscrew two bolts.


5. To reject back a support concerning the holder and to take brake колодки.
6. Cautiously to press the piston in a support by means of a corresponding wooden core, being careful not to damage an elastic casing of the piston. In case of need it is possible to remove preliminary a little a brake liquid from a tank.
7. To check up a condition of a brake disk and an elastic casing of the piston.
8. To establish on corresponding places brake колодки with an antivibrating lath, to turn a support in a direction of its holder.
9. To tighten a bolt of fastening of a support the moment of 32 Nanometers.
10. In the same way to replace brake колодки in the second forward brake.
11. To establish wheels, to lower the car and to tighten nuts of fastening of wheels.
12. Some times strongly to press a brake pedal to result in contact brake колодки with a brake disk.

13. In case of need to add quantity of a brake liquid in a tank.


CARS WITH ENGINES 2,0 ДМ3

Replacement

PERFORMANCE ORDER
1. To weaken nuts of fastening of forward wheels.
2. To lift and fix in front of the car, to remove forward wheels.
3. Cautiously to pick up a screw-driver and to take скобу fastenings of a support of a brake.
4. By means of a key for internal шестигранников 7 mm to unscrew two directing fingers of a support.
5. To disconnect sockets of wires of the gauge of deterioration brake колодок.
6. To disconnect a support from the holder and to suspend it to a body by means of a wire (without unscrewing of connection of brake hoses).
7. To take from a support internal brake колодку and external brake колодку from directing колодок.
8. Cautiously to press the piston in a support by means of a corresponding wooden core, being careful not to damage an elastic casing of the piston. In case of need it is possible to remove preliminary a little a brake liquid from a tank.
9. To check up a condition of a brake disk and an elastic casing of the piston.
10. To establish internal brake колодку in a support and to press into the piston a spring internal колодки. To establish external brake колодку in directing a support.
11. To establish a support in directing and to screw up two directing fingers of a support, tightening their moment of 20 Nanometers.
12. To establish on a corresponding place скобу fastenings of a support of a brake.
13. In the same way to replace brake колодки in the second forward brake.
14. To establish wheels, to lower the car and to tighten nuts of fastening of wheels.
15. Some times strongly to press a brake pedal to result in contact brake колодки with a brake disk.

16. In case of need to add quantity of a brake liquid in a tank.